Radiators are: industrial cooling radiators, cooling radiators civilian, civilian thermal heating radiator
Industrial cooling radiators: major equipment used in heat, cooling, and other aspects of the environment
Civil radiator: The main application in the heat of civilian equipment. If cpu radiator, and so on
Civil heating radiator is: with winter heating cooling equipment to distinguish between material can be divided into: 1. Cast iron radiator 2. Steel radiator .3 non-ferrous metal radiator 4 composite radiator.
Now China’s main civilian application of heating radiators in the northern Yunnan-Guizhou Plateau and the Northwest Territories. Production base and more focused on: Jizhou city of Hebei Province. Qingxu areas in Shanxi Province.
All “radiant” (ie. heat radiates from hot water) systems need to be bled, or purged of air, on occasion.
If there is air (or other gases such as Hydrogen) trapped inside the radiator, then the water cannot rise to the top, and only the bottom area gets hot. A bleed screw near the top of the radiator allows the trapped air to be ‘bled’ from the system, and thus restore correct operation. Often radiators located on upper floors will accumulate more air than ones on lower floors as the air will tend to rise to the topmost point in the system. These may have to be bled more often. Usually radiators are bled once or twice per season, or as needed. Another reason to exclude air is to minimise corrosion of the steel pressed radiators. Note that most central heating systems need a corrosion inhibitor added into the circulating hot water, so that the production of Hydrogen is minimised. This is created in untreated systems, by the action of the hot water on the iron in the absence of air (stripping off the oxygen atom to leave hydrogen as H2 when iron oxide is created). Note that if air is getting into the radiators frequently, this may be the sign of a leak somewhere, such as a dripping valve, or loose joint.
The current trend in radiant heating is towards underfloor heating, where radiator warm water is circulated under the entire floor of each room in a building. A network of pipes, tubing or heating cables is buried in the floor, and a gentle heat rises into the room. Because of the large area of this type of radiator, the floor only needs to be heated a few degrees above the desired room temperature, and as a result, convection is almost non-existent. These systems are reputed to have a high level of comfort, but are generally difficult to install into existing buildings. For best results, a floor covering that conducts heat well (such as tiles) should be used.
The hypocaust was a Roman heating system using a similar principle of operation.
The towel warmer is elegance European style designed with high thermal conductivity.
2. It is long lifespan, fast weld, anti-oxidize and never fade in color.
3. The heater is made of stainless steel with different kinds of shape, such as D shape, round shape, square shape and so on.
4. The towel radiator’s surface is plastic spray or chrome-plated. Also we can produce electric towel warmer .
5. The products are widely used in bathroom, living room and bedroom.
| Photo |  |
 |
A more recent type of heater used in homes is the fan assisted radiator. It contains a heat exchanger fed by hot water from the heating system. A thermostatic switch senses the heat and energises an electric fan which blows air over the heat exchanger.
Advantages of this type of heater are its small size and even distribution of heat around the room. Disadvantages are the noise produced by the fan, and the need for an electricity supply.
A conventional hot-water radiator consists of a sealed hollow metal container, usually flat in shape. Hot water enters at the top of the radiator by way of pressure, from a pump elsewhere in the building, or by convection.
As it gives out heat the hot water cools and sinks to the bottom of the radiator and is forced out of a pipe at the other end. The pipe either has a large surface area or attached fins to increase its surface area and therefore contact with surrounding air. The air near a radiator is then heated and produces a convection current in the room drawing in cold air to heat.
If set up improperly, radiators, and their supply and return pipes, can make loud banging noises like someone hammering on the pipes. This is due to either the pipes rubbing on surrounding surfaces while expanding and contracting due to heat changes or to sudden fluctuations of the supplied water pressure. Proper mounting of the radiators and supply pipes will reduce expansion noises, while upward-mounted stub ends with a trapped bubble of air (not interfering with flow, as would an un-bled radiator) will provide a cushion against pressure fluctuations, an anti-hammer device.
Stereotypical cast iron radiators (as pictured) are no longer common in new construction, replaced mostly with copper pipes which have aluminum fins to increase their surface area. In the U.K., modern domestic radiators tend to be of sheet steel construction (often with steel fins), though copper/aluminium is often found in industrial Air Handling System heat exchangers.
The radiator was invented in 1855 by Franz SanGalli. He was the first to produce a system of central heating and patented his invention in Germany and the US.
There are many designs and varieties of radiators, from conventional to modern style. Radiators are sometimes seen as an art form, much like sculpture.
All “radiant” (ie. heat radiates from hot water) systems need to be bled, or purged of air, on occasion.
If there is air (or other gases such as Hydrogen) trapped inside the radiator, then the water cannot rise to the top, and only the bottom area gets hot. A bleed screw near the top of the radiator allows the trapped air to be ‘bled’ from the system, and thus restore correct operation. Often radiators located on upper floors will accumulate more air than ones on lower floors as the air will tend to rise to the topmost point in the system. These may have to be bled more often. Usually radiators are bled once or twice per season, or as needed. Another reason to exclude air is to minimise corrosion of the steel pressed radiators. Note that most central heating systems need a corrosion inhibitor added into the circulating hot water, so that the production of Hydrogen is minimised. This is created in untreated systems, by the action of the hot water on the iron in the absence of air (stripping off the oxygen atom to leave hydrogen as H2 when iron oxide is created). Note that if air is getting into the radiators frequently, this may be the sign of a leak somewhere, such as a dripping valve, or loose joint.
A conventional hot-water radiator consists of a sealed hollow metal container, usually flat in shape. Hot water enters at the top of the radiator by way of pressure, from a pump elsewhere in the building, or by convection.
As it gives out heat the hot water cools and sinks to the bottom of the radiator and is forced out of a pipe at the other end. The pipe either has a large surface area or attached fins to increase its surface area and therefore contact with surrounding air. The air near a radiator is then heated and produces a convection current in the room drawing in cold air to heat.
If set up improperly, radiators, and their supply and return pipes, can make loud banging noises like someone hammering on the pipes. This is due to either the pipes rubbing on surrounding surfaces while expanding and contracting due to heat changes or to sudden fluctuations of the supplied water pressure. Proper mounting of the radiators and supply pipes will reduce expansion noises, while upward-mounted stub ends with a trapped bubble of air (not interfering with flow, as would an un-bled radiator) will provide a cushion against pressure fluctuations, an anti-hammer device.
Stereotypical cast iron radiators (as pictured) are no longer common in new construction, replaced mostly with copper pipes which have aluminum fins to increase their surface area. In the U.K., modern domestic radiators tend to be of sheet steel construction (often with steel fins), though copper/aluminium is often found in industrial Air Handling System heat exchangers.
The radiator was invented in 1855 by Franz SanGalli. He was the first to produce a system of central heating and patented his invention in Germany and the US.
There are many designs and varieties of aluminum radiators, from conventional to modern style. Radiators are sometimes seen as an art form, much like sculpture.
Tower Ventilator For Panel (Top Fan Filter)
Tower ventilator used on panel: 1) wind speed:0.2 - 0.5m/S ; 2) noise: <=60db ; 3) power:220v,50hz ; 4) highly efficient filter clapboard Guaranteeing purification ; 5) excellent performance ; 6) uses a taiwan-made highly-efficient centrifugal air blower ; 7) long life span, low noise, low vibration ; 
5-year quality guarantee.
Manifold and Distribute
This manifold (distribute) is used for underfloor heating.
Underfloor Heating and Cooling System
1) No water condensation on the surface of floor ; 2) Humidity is controled automatically ; 3) Temperature of each room can be setup freely ; 4) Open and close of each room can be selected freely ; 5) Flesh air can enter each room ; 6) Underfloor heating can be used in winter ; 7) The most advanced underfloor heating and cooling system all over the world
Thermostat Valve
1) Used for radiator ; 2) Size: 3/4″ ; 3) Long distance type is optional
Pipe Position Aluminium Panel
1) Thickness of aluminium layer: 0.4mm ; 2) Thickness of XPS insulation layer: 25mm ; 3) Size of panel: 260 x 500/two slots
Underfloor Heating Unit
1) Model no.: 13A 15A 25A 31A ; 2) Cooling capacity: 48,000 - 120,000Btu/h ; 3) Options: cooling only, cooling and heating ; 4) Refrigerant: R22 ; 5) Working condition: T1 ; 6) Power supply: 380V/3/50Hz or 60Hz ; 7) Reliable performance ; Ultra comfortable heating performance compare with auxiliary electric heat source
Hot-Water Producing Chiller
1) This unit is perfect integration with air cooled chiller and heat pump water heater ; 2) This kind of unit can supply for 50-60 centigrade living hot-water with the exception that be able to provide cooling in the summer and heating in the winter ; 3) This unit will absolutely replace the investment for boilers ; 4) During A/C working summer, the outdoor unit will discharge 50 centigrade hot gas ; 5) Taking advantage of the hot gas, air cooled chiller with hot-water return covert the thermal energy to free living hot-water ; 6) Then free hot water is available during the whole cooling season ; 7) During the winter, air cooled chiller with hot-water return absorb thermal energy from atmosphere (same working theory as heat pump water heater) and transfer it to water until the water temperature go up to 50 centigrade ; The cost for the hot water is only 1/3 of the electric boilers and 40 percent
of the fueling boilers ; 9) Suitable places: hotel, sauna center, baths, school, family, beauty and hair-dressing, saloon and villa etc.towel warmer
Floor Air Register
1) For floor application ; 2) All steel construction ; 3) Multi-angle fin setting ; 4) aluminu radiator Rolled fin for strength and safety ; 5) Heavy gauge stamped face and welded construction ; 6) Available with mounting screw holes ; 7) White or bright brown powder-coating finish ; Any color you would like (2 weeks more) ; 9) Available in 2 x 10, 2 x 12, 2 x 14, 4 x 8, 4 x 10, 4 x 12, 4 x 14, 6 x 10, 6 x 12, 6 x 14
Simple to install radiators for locations where plumbing might be difficult. Our radiators contain water just like a central heating radiator but has the advantage of having its own heating element. This means you are not losing the heat in the water as it travels from the boiler to the radiator. Our radiators only requires a standard plug socket to power the heater - where you can get electricity you can get heat! The system is ideal for conservatories, listed buildings, flats or any other location where installing a ‘plumbed in’ radiator will be problematic. Listed below are our selection of electric radiators currently available from the radiator centre. The list below is in alphabetical order (left to right) to view details such as technical specifications and current price ranges click on the thumbnail image or the model name.
The adoption of European-style aluminum radiator fins in radiator complies with the long-winged design in fluid mechanics. 2) The special aluminum alloy has good thermal conductivity and is capable of producing heat under max power output. 3) Process of degreasing and oxidation of radiator surface prior to spray painting, which ensures that the paint will not fall off. 4) The water chamber is twice treated against corrosion to ensure it is corrosion-proof while operating in pH<12 water. 5) The complete test method, including 1.6Mpa hydro test and alternating cold and heat test under the pressure for the individual fin and for the fin group is a good guarantee of the safety and reliability of products.
Swim Pool Heater
1) Tubular heat exchanger ; 2) The copper pipe adopts copper tubing which is nickel plated ; 3) The cover, all pipes and connections are stainless steel
White-Painted Flat Towel Rail Heater
1) Advantages: a long lifespan, economical, and high efficiency. 2) Applications: widely applied in living room, bathroom, bedroom and kitchen. 3) Stylish shape and excellent quality. 4) White-plated surface treatment. 5) Specification: 1,200 x 500mm, 800x 500mm, etc. 6) Material: high grade mild steel, with 25mm diameter horizontal tube and 40 x 30 D type vertical tube
Aluminum Tube Heater Series
It adopts rating voltage of 250V below, 50-60Hz, relevant humid less than 90%, environment temperature of -30 - +50°C for power and heat. It has rapid speed on heat and with equality, security, through control on power density, insulation material, temperature switch and heat scatter conditions can be required wind generator on temperature. It is mainly for frost elimination in refrigerator, frozen elimination and other electric appliance.